diff options
Diffstat (limited to 'nixos/modules/installer/cd-dvd/sd-image-aarch64.nix')
-rw-r--r-- | nixos/modules/installer/cd-dvd/sd-image-aarch64.nix | 64 |
1 files changed, 9 insertions, 55 deletions
diff --git a/nixos/modules/installer/cd-dvd/sd-image-aarch64.nix b/nixos/modules/installer/cd-dvd/sd-image-aarch64.nix index bef6cd2fb5a..76c1509b8f7 100644 --- a/nixos/modules/installer/cd-dvd/sd-image-aarch64.nix +++ b/nixos/modules/installer/cd-dvd/sd-image-aarch64.nix @@ -1,60 +1,14 @@ -# To build, use: -# nix-build nixos -I nixos-config=nixos/modules/installer/cd-dvd/sd-image-aarch64.nix -A config.system.build.sdImage -{ config, lib, pkgs, ... }: - +{ config, ... }: { imports = [ - ../../profiles/base.nix - ../../profiles/installation-device.nix - ./sd-image.nix + ../sd-card/sd-image-aarch64-installer.nix ]; - - boot.loader.grub.enable = false; - boot.loader.generic-extlinux-compatible.enable = true; - - boot.consoleLogLevel = lib.mkDefault 7; - - # The serial ports listed here are: - # - ttyS0: for Tegra (Jetson TX1) - # - ttyAMA0: for QEMU's -machine virt - # Also increase the amount of CMA to ensure the virtual console on the RPi3 works. - boot.kernelParams = ["cma=32M" "console=ttyS0,115200n8" "console=ttyAMA0,115200n8" "console=tty0"]; - - boot.initrd.availableKernelModules = [ - # Allows early (earlier) modesetting for the Raspberry Pi - "vc4" "bcm2835_dma" "i2c_bcm2835" - # Allows early (earlier) modesetting for Allwinner SoCs - "sun4i_drm" "sun8i_drm_hdmi" "sun8i_mixer" - ]; - - sdImage = { - populateFirmwareCommands = let - configTxt = pkgs.writeText "config.txt" '' - kernel=u-boot-rpi3.bin - - # Boot in 64-bit mode. - arm_control=0x200 - - # U-Boot used to need this to work, regardless of whether UART is actually used or not. - # TODO: check when/if this can be removed. - enable_uart=1 - - # Prevent the firmware from smashing the framebuffer setup done by the mainline kernel - # when attempting to show low-voltage or overtemperature warnings. - avoid_warnings=1 - ''; - in '' - (cd ${pkgs.raspberrypifw}/share/raspberrypi/boot && cp bootcode.bin fixup*.dat start*.elf $NIX_BUILD_TOP/firmware/) - cp ${pkgs.ubootRaspberryPi3_64bit}/u-boot.bin firmware/u-boot-rpi3.bin - cp ${configTxt} firmware/config.txt - ''; - populateRootCommands = '' - mkdir -p ./files/boot - ${config.boot.loader.generic-extlinux-compatible.populateCmd} -c ${config.system.build.toplevel} -d ./files/boot - ''; + config = { + warnings = [ + '' + .../cd-dvd/sd-image-aarch64.nix is deprecated and will eventually be removed. + Please switch to .../sd-card/sd-image-aarch64-installer.nix, instead. + '' + ]; }; - - # the installation media is also the installation target, - # so we don't want to provide the installation configuration.nix. - installer.cloneConfig = false; } |